Steering

  • Knuckle Stud

    Factory Toyota knuckle hardware. Fits 1979-1985 Toyota front solid axle knuckle and a 1990-1997 Toyota FJ80 Landcruiser.

    ONLY 5.39

    Choose Options
  • Sector Shaft Nut and Washer

    Replacement nut and washer for bolting on pitman arm to steering box. Fits 4wd IFS steering box from 1986-1995 Pickup and 4Runner.

    ONLY 4.59

    Buy Now
  • Fitting, PS Box, M16-1.5 HP

    This special fitting is used to connect the high pressure steering hose to the steering box. Steering Box, High Pressure Fitting, 130511-1-KIT

    ONLY 10.69

    Buy Now
  • Spindle Bearing Nut Kit

    Normally the nuts that hold the wheel bearings can be reused over and over again. If your wheel bearing retainer nuts need replacing this kit is for you. Kit contains 2 nuts, star washer and flat index washer

    ONLY 12.29

    Buy Now
  • TG Super Metal Knuckle Stud (single)

    Stronger and longer than stock Toyota replacement knuckle studs and more affordable than our Magnum Studs these studs will provide great strength without breaking the bank.

    ONLY 13.79

    Buy Now
  • Knuckle Pull Scale

    A pull scale is helpful in setting up the shims on a knuckle. By increasing the shims above and below the knuckle the knuckle becomes tighter.

    ONLY 15.39

    Buy Now
  • Knuckle, Stud, Hex, ARP

    Trail-Gear Magnum knuckle studs are stronger than any other stock replacement Toyota knuckle stud on the market. These heavy-duty studs are manufactured to our specifications by world-renowned bolt manufacturer ARP (Automotive Race Products). Each stud is made from super tough, ARP 2000 material and is hardened to 220,000 PSI. Magnum studs are .250" (1/4

    ONLY 19.99

    Buy Now
  • Low Pressure Return Fitting

    Low Pressure Return Fitting, 130508-1-KIT

    ONLY 19.99

    Buy Now
  • Tacoma Steering Shaft Seal

    OEM Replacement Steering Shaft Seal. Fits into the Tacoma Firewall and other stock Toyota applications.

    ONLY 15.39

    Buy Now
  • Knuckle Hardware

    Magnum Stud

    ONLY 17.09

    Buy Now
  • Camber Adjustment Bushing

    This 0° Camber/Caster fits the Rock Assault™ 9 Inner C. 2 of each are required for one front axle housing

    ONLY 29.19

    Buy Now
  • Rock Ring: Kit, 4 Pcs

    We have had a lot of people tell us they dont like the stock inner felt plates because they are so thin and are easily damaged in the rocks. Well check out this trick solution.

    ONLY 38.39

    Buy Now
  • Weld-In Steering Rod Bungs

    Finally a weld in bung with the thread pitch of an FJ80 TRE, which is the most commonly used TRE in Toyota hi-steer kits. Once welded into your tie rod or drag link, this bung will allow you to make a custom length steering shaft in minutes.

    ONLY 36.79

    Buy Now
  • Weld On Steering Wheel Disconnect 3/4" OD

    Trail-Gears weld on steering wheel disconnect uses a solid billet steel hex shaft that you weld over your existing steering shaft or steering column. Then you would bolt our billet aluminum quick disconnect unit to your steering wheel. This system allows you to quickly disconnect your steering wheel by simply pushing a button on the quick disconnect. Our weld on steering wheel disconnect is ideal for buggies and truggies on dirt, mud, or sand. Competition tested and used by some of the world

    ONLY 44.49

    Buy Now
  • Rock Assault Steering Stops

    A good set of steering stops is critical so that your steering does not over travel and damage other steering or axle components.

    ONLY 44.49

    Buy Now
  • Low Pressure IFS Steering Box Fitting

    Low Pressure IFS Steering Box Fitting, 130510-1-KIT

    ONLY 42.99

    Buy Now