Steering

  • Knuckle Stud

    Factory Toyota knuckle hardware. Fits 1979-1985 Toyota front solid axle knuckle and a 1990-1997 Toyota FJ80 Landcruiser.

    ONLY 5.39

    Choose Options
  • Fitting, PS Box, M16-1.5 HP

    This special fitting is used to connect the high pressure steering hose to the steering box. Steering Box, High Pressure Fitting, 130511-1-KIT

    ONLY 10.69

    Buy Now
  • Knuckle Pull Scale

    A pull scale is helpful in setting up the shims on a knuckle. By increasing the shims above and below the knuckle the knuckle becomes tighter.

    ONLY 15.39

    Buy Now
  • Knuckle, Stud, Hex, ARP

    Trail-Gear Magnum knuckle studs are stronger than any other stock replacement Toyota knuckle stud on the market. These heavy-duty studs are manufactured to our specifications by world-renowned bolt manufacturer ARP (Automotive Race Products). Each stud is made from super tough, ARP 2000 material and is hardened to 220,000 PSI. Magnum studs are .250" (1/4

    ONLY 19.99

    Buy Now
  • Low Pressure Return Fitting

    Low Pressure Return Fitting, 130508-1-KIT

    ONLY 19.99

    Buy Now
  • Camber Adjustment Bushing

    This 0° Camber/Caster fits the Rock Assault™ 9 Inner C. 2 of each are required for one front axle housing

    ONLY 29.19

    Buy Now
  • Weld-In Steering Rod Bungs

    Finally a weld in bung with the thread pitch of an FJ80 TRE, which is the most commonly used TRE in Toyota hi-steer kits. Once welded into your tie rod or drag link, this bung will allow you to make a custom length steering shaft in minutes.

    ONLY 36.79

    Buy Now
  • Weld On Steering Wheel Disconnect 3/4" OD

    Trail-Gears weld on steering wheel disconnect uses a solid billet steel hex shaft that you weld over your existing steering shaft or steering column. Then you would bolt our billet aluminum quick disconnect unit to your steering wheel. This system allows you to quickly disconnect your steering wheel by simply pushing a button on the quick disconnect. Our weld on steering wheel disconnect is ideal for buggies and truggies on dirt, mud, or sand. Competition tested and used by some of the world

    ONLY 44.49

    Buy Now
  • Rock Assault Steering Stops

    A good set of steering stops is critical so that your steering does not over travel and damage other steering or axle components.

    ONLY 44.49

    Buy Now
  • Low Pressure IFS Steering Box Fitting

    Low Pressure IFS Steering Box Fitting, 130510-1-KIT

    ONLY 42.99

    Buy Now
  • PS Pulley (V-Belt)

    This pulley is designed to fit our standard or full hydraulic power steering pumps. Power Steering Pump Pulley, 130503-1-KIT

    ONLY 59.89

    Buy Now
  • Steering Column - 3 1/4"

    This steering column will allow you to use your existing Toyota steering linkage without having to buy a coupler and then cut and weld on your steering shaft. This steering column measures 3 1/4 inches from the base of the flange to the outer edge of the shaft, and fits most brands of steering valves (Orbitals) that are commonly used in this application.

    ONLY 90.59

    Buy Now
  • PS Cooler

    If you're running a high volume/pressure pump your system is generating much more heat then the stock system. Fluid overheating can cause damage to steering pump and steering box.

    ONLY 121.29

    Buy Now
  • Knuckle Sandwich

    If you don’t want busted knuckles on the trail, you need Trail-Gear’s Knuckle Sandwich. The Trail-Gear Knuckle Sandwich is everything you need to service your knuckles

    ONLY 366.89

    Buy Now